language
中国
韩国
韩国
韩国
韩国
韩国
×

Search

Search
News
news
Check category
/
/
/
Matters needing attention when changing glue for thermal bonding machine

Matters needing attention when changing glue for thermal bonding machine

(Summary description)When cleaning the thermal bonding machine, the hot-melt glue heating plate must be separated from the PUR hot-melt glue bucket first. After the PUR hot-melt glue bucket is separated from the heating plate of the PUR hot-melt glue machine, it should be Cut off all power.

Matters needing attention when changing glue for thermal bonding machine

(Summary description)When cleaning the thermal bonding machine, the hot-melt glue heating plate must be separated from the PUR hot-melt glue bucket first. After the PUR hot-melt glue bucket is separated from the heating plate of the PUR hot-melt glue machine, it should be Cut off all power.

Information

When cleaning the thermal bonding machine, the hot-melt glue heating plate must be separated from the PUR hot-melt glue bucket first. After the PUR hot-melt glue bucket is separated from the heating plate of the PUR hot-melt glue machine, it should be Cut off all power.

thermal bonding machine
When the thermal bonding machine takes off the barrel, the air pressure charged should be gradually pressurized from small to large. Under any circumstances, it is not allowed to directly use the high-pressure gas to directly take off the barrel to avoid accidents.
When the heating plate of the thermal bonding machine is separated from the polyurethane hot-melt glue bucket, before cleaning the residual glue of the PUR hot-melt glue, the special structure on the pressure plate of the PUR hot-melt glue machine must be used to close the channel between the pressure plate and the pump body. Prevent curing.
When cleaning the heating platen of the thermal bonding machine, the staff must wear special high temperature resistant protective clothing and high temperature resistant gloves. Do not let the skin touch the high temperature parts such as the hot melt adhesive bucket, molten PUR hot melt adhesive and heating plate to avoid burns.
When the thermal bonding machine takes off the barrel, the best way is to fill the 55-gallon hot melt glue barrel with dry nitrogen, and avoid using undried compressed air directly. Dry thoroughly. And often check the use of desiccant.
After the thermal bonding machine is separated from the hot-melt glue bucket, the residual PUR hot-melt glue on the hot-melt glue pressure plate must be thoroughly cleaned immediately. Scratched platen Teflon coating.
When cleaning the pressure plate of a thermal bonding machine with a special structure, the heating plate of the PUR hot melt machine cannot completely clean the residual PUR hot melt adhesive in a short time due to the special structure, so dry nitrogen protection must be used when cleaning the residual PUR hot melt adhesive, and The time for cleaning the residual glue shall not exceed 10 minutes, and no hard tools shall be used to clean the heating plate of the PUR hot melt adhesive machine.
After cleaning the pressure plate of the thermal bonding machine, immediately press the pressure plate into a new PUR hot-melt glue bucket to avoid exposing the pressure plate to the air for a long time. When pressing the heating plate into the plastic bucket, the air pressure of the lifting cylinder should be from small to large, and high-pressure gas should not be used directly to prevent accidents and pay attention to the safety of operators.
When the pressure plate of the thermal bonding machine is pressed into the rubber barrel, a small amount of silicone oil can be properly smeared on the sealing ring of the pressure plate for lubrication, so as to produce lubrication between the pressure plate and the rubber barrel and protect the use of the sealing ring.
When the heating platen of the thermal bonding machine is pressed into the new polyurethane hot melt adhesive bucket, the overflow valve should be opened to completely remove the residual air in the plastic bucket, and the PUR hot melt adhesive with air bubbles should be removed to avoid air The polyurethane hot melt adhesive flows into the throat of the pump body hot melt adhesive machine.
After the pressure plate of thermal bonding machine is placed in the polyurethane hot-melt glue barrel and the air is exhausted, the glue overflow valve is tightly locked. At this time, the air pressure in the stroke cylinder can be appropriately increased to make the work smoother.
After replacing the PUR hot melt adhesive, you must wait for the thermal bonding machine to heat for at least 30 minutes before starting the gear pump and motor. If the gear pump and motor are started immediately, it will damage the melter gear pump and reduce the service life of the melter.

Keyword:

Hot Spot

12-26
2022
The characteristics of quality Disc Heel Forming Machine Single cold

The characteristics of quality Disc Heel Forming Machine Single cold, the rubber machine is a fully automatic injection molding machine, the machine can complete precise molding within the set parameters.

12-19
2022
Features of Disc Heel Forming Machine Single cold products

Shoemaking equipment for producing plastic soles, especially a Disc Heel Forming Machine Single cold products with a liftable injection head. It is characterized in that a hydraulically driven lifting mechanism is connected under the injection machine head.

12-12
2022
The working principle and application of quality Disc Heel Forming Machine Single cold

The quality Disc Heel Forming Machine Single cold is the main forming equipment for making thermoplastics or thermosetting materials into various shapes of plastic products with plastic forming molds.

12-05
2022
What are the tuning methods and techniques of Disc Heel Forming Machine Single cold

Disc Heel Forming Machine Single cold injection process pressure is divided into two types: plasticizing pressure and injection pressure, which directly affect the plasticizing of plastics and product quality.

11-28
2022
How to choose quality Glue spray robot

The quality Glue spray robots can be programmed down to the millimeter and have the ability to dispense fluid or adhesive more accurately and evenly than other processes. Again, repeatability plays a big role here.

11-21
2022
What are the advantages of Glue spray robot

The main benefits of Glue spray robots include increased cost-effectiveness and time savings. However, given that robots are used in applications such as small component assembly, these efficiencies can be even higher.

11-14
2022
What processes are needed to develop a new Direct injection shoe making machine products

If a shoe manufacturer wants to produce a pair of good shoes, it must first have a good direct injection shoe making machine products machinery and equipment, so what processes do we need to develop a new direct injection shoe making machine products?

11-07
2022
Two systems for daily maintenance of thermal bonding machine

Production machines are heavy oil machinery and equipment. When a failure occurs, it takes a long time to repair, so correct maintenance and failure prevention are required. The following are the two daily maintenance items of the vertical disc thermal bonding machine for your reference.

Our Mission

Technology leads the future, intelligent manufacturing changes manufacturing
logo
img
这是描述信息

Scan and follow us

Copyright of the page Xiamen Manyu Automation Technology Co., Ltd.     闽ICP备19024249号-1     300.cn    SEO

Copyright of the page Xiamen Manyu Automation Technology Co., Ltd. 

 闽ICP备19024249号-1   

300.cn    SEO

×